Otherwise, your computer may not start properly. Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. To avoid damage to the drive, do not set it on a hard surface. If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. Ground yourself by touching an unpainted metal surface on the back of the computer.
|Date Added:||16 March 2009|
|File Size:||41.12 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
The mounting-bracket screws need to be removed for the removal of the system board.
You can do so by touching an unpainted metal surface on the computer chassis. To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network port or device.
Specifications: Dell Dimension /E Service Manual
If the DDR2 memory modules are not installed in matched pairs, the computer will continue to operate, but with a slight reduction in performance. To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the computer.
Note the routing of the DC power cables underneath the routing clips in the computer frame as you remove them from the system board and drives. See the label on the module to determine the module’s capacity.
FlexBay for optional floppy drive or optional Media Card Reader. Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation. Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the computer. See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting. Always install DDR2 memory modules in the order indicated on the system board.
If you are installing or replacing a card, follow the procedures in the next section. If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you replace the processor. Remove the card before connecting the floppy-drive cables. To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
To connect a network cable, first plug the cable into the network port or device, and then plug the cable into the computer. Most interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector. Use the pull-tab to remove the data cable from your hard drive or from the system board. If you installed a processor replacement kit from Dell, return the original heat-sink assembly and processor to Dell in the same package in which your replacement kit was sent.
When you install the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage to the thermal interface material.
See the documentation that came with the drive for instructions on installing any software required for drive operation. Ensure that the assembly has had sufficient time to cool before you touch it. Some network adapters automatically start the computer when they are connected to a network.
To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module.
When installing the processor, do not touch any of the pins inside the socket or allow any objects to fall onto the pins in the socket. DDR2 memory modules should be installed e150 pairs of matched memory size, speed, and technology. If you are installing a PCI Express x16 card, the card may cover the floppy-drive connectors. Snap the bracket onto the new drive.
For additional information pc the type of memory supported by your computer, see your Owner’s Manual. When installing the heat-sink assembly, do not touch the thermal interface on its underside, as this may result r510 damage. To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer. If your replacement hard drive does not have the hard drive bracket attached, remove the bracket from the old drive by unsnapping it from the drive.
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.
Cables routed over the cards can prevent the computer cover from closing properly or cause damage to the equipment.